Most of the adult life dedicated work. The structure of the labor office staff includes permanent eye strain, whether it is working with paper documents or electronic documents. It is estimated that over eight o'clock working day man about ten thousand times takes a view from the document on the monitor and keyboard. Therefore, at first, when planning the repair cost would be to focus on the conditions and level of illumination of classrooms. It must be remembered that the lack of coverage often leads to premature fatigue eye, uncomfortable sensations, pains of the head. Stuffiness in overdried room, the bright glare, inadequate lighting – both result, the slowness of inoperability. Moreover, in a dimly lit office, most employees fall victim to "visual syndrome>> that is increasing morbidity servants, therefore, losses company to pay for sick leave. Lighting and office space should be solely functional, lamps must not give glare and flare. Level of illumination and the light should be similar to daylight. Ideal use for this fluorescent lamps or energy saving lamps white shade. Ebay often addresses the matter in his writings. Everything else, fluorescent lamps, and they alone do not give a glare on the monitor screen. Consequently, for the illumination of workplaces office workers is recommended whenever possible to equip istsentnymi phosphor lamps. When planning the lighting to be understood that the main task lighting is to provide ideal conditions for reading small print in documents, tiny details in the plans. Aesthetics of interior design in this case concede the primacy of the quality and usefulness. When developing a light industrial premises, as well as shops, book repositories and warehouses, in most cases use of natural light, which is complementary to the artificial, if necessary. Illumination in industrial premises should provide lack of harsh shadows that can give the wrong impression about the shape and size of the object. For dispersing the shadows of the lamps used specialized milk glass. The lamp shines calmly and evenly, without a glow on throughout the action. Where in the production room is used exclusively in natural light, it is necessary to take care of the presence of blinds, canopies, curtains, because need to get softly diffused light. Industrial lighting can be of two kinds: general and combined. General lighting can be used in business departments, where it is necessary to produce the same work. This coverage may apply, and in public places use, and in warehouses. General lighting can be uniform and localized, and if necessary, add a local lighting. In addition to industrial lighting, typically defined as bactericidal medical lamps and signal lamps used to indicate the progress of the fire room. In the case of a project, electricians, it is always subject to parsing and record all these factors, therefore, to create a literacy project, as well as and following them electro-installation works best to contact the firm where professionals work.

Instead of plastering the solution can be applied plaster sheets of drywall or fiberboard (tiles). Sheets of gypsum drywall composed of plaster in its pure form or with mineral or organic additives, coated cardboard on all four sides, except for frontal faces. Fibreboard are extra-hard, solid, semisolid, and others. Veneer of all types of surfaces. By wooden leaf surface nail with a broad hat (Tolev). sheets cut with a knife or sawing saw or hacksaw. To brick, stone, concrete surface of the plate or plates bonded with sealant, prepared by different recipes. Most of the mastic is not very rapid. It is convenient to work, as it gives an opportunity to start setting mastic cope with attaching sheets. Sheets are fixed in different ways. You can put in a corner whole sheet. In this case, make a groove in the middle of the sheet and bend it at right angles, forming a husk. Entire lists can start pasting from the corner, forming a peel sheet edges. These methods are quite different from each other by quality and durability. With that and the other way first surface and arrange support beacons or marks. Before starting work, all surfaces should be divided into equal to the width of the leaves are used. Line grips must be strictly vertical, so they must fight off namelennym cord. Then start tracing. Under the sheets make reference marks of 80 * 80 mm. On each vertical line must be at least three brands. Brands have exactly along the lines in such a way that they could prop up edges two sheets. After the device reference marks on all surfaces exposed to the veneer, proceed to the fastening sheet. Necessary The number of sheets should be prepared in advance. All coated surfaces can be painted or wallpaper three days after finishing.